Viconics VTR7300 Installation Manual Uživatelský manuál

1 | PIR Ready VTR7300 Series-Installation Guide CONTENTS Installation 2 Location 2 Installation 2 Operation Overview 3 Model Chart 5 Netw

10 | PIR Ready VTR7300 Series-Installation Guide USER INTERFACE Unoccupied mode override An Override can be made on commercial models d

11 | PIR Ready VTR7300 Series-Installation Guide Dual occupied setpoints adjustment (Local occupied setpoint adjustment when “Stp Func” = Dual Stp)

12 | PIR Ready VTR7300 Series-Installation Guide AutoMode set to OFF = Auto system mode NOT ACTIVE SEQUENCE SELECTED MODE MENU 0 = Cooling Only Off

13 | PIR Ready VTR7300 Series-Installation Guide access to all configuration properties of the Terminal Equipment Controller. Entering a wrong passwo

14 | PIR Ready VTR7300 Series-Installation Guide PAN ID Personal Area Network Identification Default value = 0 Range is: 0 to 1000 Conditional p

15 | PIR Ready VTR7300 Series-Installation Guide Get From Terminal Equipment Controller Get From another device configuration utility Default value

16 | PIR Ready VTR7300 Series-Installation Guide BI 2 Binary input no.2 configuration Default value = None (None): No function will be associated w

17 | PIR Ready VTR7300 Series-Installation Guide RUI 1 Cont’d  Contact opened = No alarm  Contact closed = Alarm displayed (Service): A backl

18 | PIR Ready VTR7300 Series-Installation Guide %RH disp Local %RH Display Default value = Off Models with Humidity sensor only Conditional param

19 | PIR Ready VTR7300 Series-Installation Guide SeqOpera Sequence of operation Default is: Sequence #1 Selects the initial sequence of operation re

2 | PIR Ready VTR7300 Series-Installation Guide INSTALLATION Remove the security screw on the bottom of Terminal Equipment Controller cover. 

20 | PIR Ready VTR7300 Series-Installation Guide %RH set Dehumidification setpoint Default is 50 % RH Conditional parameter to Humidity models VTR

21 | PIR Ready VTR7300 Series-Installation Guide Unocc HT Unoccupied heating setpoint Default value = 62 °F Unoccupied heating setpoint range is

22 | PIR Ready VTR7300 Series-Installation Guide Set Type Temporary setpoint enable Default is : Permnent Enables temporary setpoints feature to a

23 | PIR Ready VTR7300 Series-Installation Guide Auto Fan Auto Fan Function Default value: AS Auto Speed Fan Mode operation for Fan Sequences 2

24 | PIR Ready VTR7300 Series-Installation Guide SPECIFICATIONS Terminal Equipment Controller power requirements: Operating conditions: Storage co

25 | PIR Ready VTR7300 Series-Installation Guide DRAWING & DIMENSIONS Viconics Technologies Inc. Tel.: Fax: Toll free:w

3 | PIR Ready VTR7300 Series-Installation Guide 12. Re-Install wiring terminals in their correct locations (fig. 3). 13. Re-install the cover (top

4 | PIR Ready VTR7300 Series-Installation Guide 2 or 4 pipe only with electric reheat can be configured and wired for the following: o Cooling onl

5 | PIR Ready VTR7300 Series-Installation Guide MODEL CHART

6 | PIR Ready VTR7300 Series-Installation Guide Network ready  All Viconics VTR7300 series Terminal Equipment Controllers are designed for stand-al

7 | PIR Ready VTR7300 Series-Installation Guide From the VTR73xxA to the first VC3xxxX Relay Pack  Uses existing or new field wires  A minimum o

8 | PIR Ready VTR7300 Series-Installation Guide Wiring of local inputs to VTR73xxA Terminal Equipment Controller CONFIGURING AND STATUS DISPLA

9 | PIR Ready VTR7300 Series-Installation Guide % RH display is conditional to: (Humidity display is model and configuration dependent)  Model with